![]() |
|
![]() |
|
![]() |
|
![]() |
|
![]() |
|
![]() |
|
![]() |
![]() |
![]() |
![]() |
|
|
|
|||||||
| Register | Home | Forums | Active Topics | Photo Gallery | Search | Today's Posts | Mark Forums Read | Motorcycle Escrow |
![]() |
|
|
LinkBack | Thread Tools |
|
|
#1 (permalink) |
|
:::Z-250 Rider:::
Join Date: Jun 2011
Location: Medina, Ohio
Posts: 489
|
I finally got to take my Z to the track for this first time after rebuild. Had a great day going, one of the bigger jumps was a 40' double.
![]() and here is a picture of how the landing should look ![]() and here is in mid air, looking good, right ![]() well I don't remember anything after the base of the jump. My brother summed it up that I was 2" to low or 2" to short. Here is where I landed, actually the staff rolled me out of the middle after the bike that was behind me landed with in inches. You can see him trying to stop the riders. ![]() I was out cold. 36 years of riding and I've never been knocked out, by far the hardest I've landed. I did get back on and ride of the track after three failed attempts at standing. ![]() 4 hour in the ER. Can't wait till next week to do it again!
__________________
September 2012 Quad of the Month Winner
2007 Z with a couple mods Engine 94mm big bore - +4 Hot Rods Crank - Webb 540/539 Cams - Wiseco Valves - KW Springs - FCR 39 Carb - K/N Filter in UM Air Box - Dana Tech programmable CDI & Coil - Full White Bros Exhaust - Dyno'd at 43.4 Hp and 32.7 Ft lbs snap-im-finally-starting-my-own-build-thread |
|
|
|
| Sponsored Links | |||
Advertisement | |||
|
|
#2 (permalink) |
|
:::Post Whore:::
Join Date: Aug 2011
Location: Boyceville, WI / Downing, WI
Posts: 1,856
|
My cousin has a 80 footer that he takes his dirtbike off of, he's crazy.
__________________
2003 Z400
Engine Mods: Big Gun ES Slip on 170 main - No Lid Wiseco Piston & Rings Suspension, Steering & Chassis: MSR Motion Bars w/ Pro Taper Clamps PRM Rear Skid Plate - DG Alloy Nerfs - LTR Pegs DWT Red Label Front Rims - UM Rad Shrouds Maxxis Razr Tires - 450r Front Shocks YFZR Front Master Cylinder - Stainless Brake Lines Misc: Modquad Block Off - ProDesign Tether ProTaper Grips - Moose Case Saver - Blob Removal 96L/40T/14T Gearing - Raptor 660 Petcock Maier Hood - Custom dash |
|
|
|
|
|
#3 (permalink) | |
|
:::Z-250 Rider:::
Join Date: Jun 2011
Location: Medina, Ohio
Posts: 489
|
Quote:
__________________
September 2012 Quad of the Month Winner
2007 Z with a couple mods Engine 94mm big bore - +4 Hot Rods Crank - Webb 540/539 Cams - Wiseco Valves - KW Springs - FCR 39 Carb - K/N Filter in UM Air Box - Dana Tech programmable CDI & Coil - Full White Bros Exhaust - Dyno'd at 43.4 Hp and 32.7 Ft lbs snap-im-finally-starting-my-own-build-thread |
|
|
|
|
|
|
#4 (permalink) |
|
:::Post Whore:::
Join Date: Jan 2011
Location: Coal Region-Pa
Posts: 2,207
|
I should of learned this a while ago. Thats when all my crashes were really. Just keep that inmind cruze the track first then hammer down.
__________________
______________________ 2006 Ltr 450 Pim 213.1 Wisco Piston Hotrod Crank Prm Summit Front Bumper Prm Grab Bar IMS Tank IMS Dry Break Tag Handle Bars Oval Tip Yoshi ARS-FX Xc A Arms LSR Xc Axle Ltz Hubs Fox Floats X Evols Fox Podium Rear Burgard Steering Stem CCP Stabilizer Precession Clamps IMS Pegs GTThunder Linkage Two9zero4 Sprocket Guard GTT Rotor Guard http://www.suzukicentral.com/forums/...tm-winner.html SPONSORS LSR GoPro Jett Boots |
|
|
|
| Sponsored Links | |
Advertisement | |
![]() |
| Thread Tools | |
|
|