|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
 |
 |
|
|
08-17-2011, 12:34 PM
|
#1 (permalink) | |
|
:::Z-250 Rider:::
Join Date: Jul 2011
Location: Duluth, MN
Posts: 433
|
Homemade a-arm gaurds?
Anyone ever make any? i searched but didn't find anything, if you did please post pics and a breif run down on how you made them.
__________________
'04 DVX 400 Moose racing bars~Moose EBrake Elim~06 KFX Rear Rotor~06 Rear brakes Homemade Ignition/Lights Switch Panel~Custom lights~Homemade Dash Custom Airbox Lid~Custom tail light and cover~Homemade Mud Screen and Heel GuardsCustom Air Scoops and Frame Guards~Tusk Hand Guards~Artrax all the way 'round Quote:
Last edited by Basket Case; 08-17-2011 at 01:14 PM. |
|
|
|
| Sponsored Links | |||
Advertisement | |||
|
08-17-2011, 04:29 PM
|
#2 (permalink) |
|
:::Vinson Rider...wtf?:::
Join Date: Jun 2009
Posts: 705
|
I did but never used them. I carefully made a good fitting card board template and then cut them out of 1/8th aluminum with variable speed jigsaw. I was going to use 3/4 conduit clamps to attach. In all reality, they can be found so cheap on here and e-bay, it's not worth the time and materials. I got a pro armor set here for @$20 shipped and another set of cobraATV for my buddy on ebay for @$14, both in like new shape with all the proper mounting hardware. In both cases I had that much already in conduit clamps and saw blades, and I already had the aluminum!
__________________
Trinity Stage 4 full exhaust, UNI filter w/ DIY powerlid, 400EX airboot, FCR39, R&D fuel screw, DRZe kit, Yoshimura Cams, Motion Pro Twist throttle, Pro Taper bars, YFZ calipers, TRX master cylinder, KX clutch perch, KTM lines, Acerbis hand guards, TrailTech Vapor, aluminum radiator shrouds, aluminum heal guards, bossbearing DLR conversion, ZX6 LED tail-light, full PRM skids and bumper, ITP's w/GNCC's, Laegers +2, Houser +1.25 |
|
|
|
|
08-17-2011, 08:32 PM
|
#3 (permalink) | |
|
:::Z-250 Rider:::
Join Date: Jul 2011
Location: Duluth, MN
Posts: 433
|
thanks ill keep an eye out,my neigbor has some extra stainless steel peices that i think ill take off his hands and make the main frame skid tho
__________________
'04 DVX 400 Moose racing bars~Moose EBrake Elim~06 KFX Rear Rotor~06 Rear brakes Homemade Ignition/Lights Switch Panel~Custom lights~Homemade Dash Custom Airbox Lid~Custom tail light and cover~Homemade Mud Screen and Heel GuardsCustom Air Scoops and Frame Guards~Tusk Hand Guards~Artrax all the way 'round Quote:
|
|
|
|
|
|
09-07-2011, 11:56 PM
|
#4 (permalink) |
|
:::LT250 Rider:::
Join Date: Dec 2008
Location: calgary alberta canada
Posts: 765
|
i made a arm guards and skid plates out of some diamond plate i found at the wreckers ($15) the plate was from an old truck toolbox. all i did was cut the plate about an inch more than what i needed and just bent them using a hammer with the a arm sitting inside as kind of like an anvil. worked out great, but i got new a arms and i figured out that the guards are very unnecessary and just collect mud, never seen a pro rider ever use them. i still use the skid plate though and it works great.
__________________
JANUARY 2012 QOTM! 03 Z, 462 motor, p&p, houser +1 arms +1 stem +1.25 swingarm, elka stage3 all around, fcr39, CFM, kibblewhite, pro design, asv, dynatek, yoshi, nshc, durablue, pro taper, galfer, pro armor, pro aluminum, armadillo, ims roll, dr. D, moose, odi, fly, DID, 13-40 gearing, frame gusseted, 22" razor I's in rear, itp xct 23" fronts. wishing for webcams 540/539 04 yfz501, venom port, venom pipe, FCI, sredrum 42.5 carb, and a lot more. |
|
|
|
| Sponsored Links | |
Advertisement | |
 |
| Thread Tools | |
|
|
