2006 Part out - Lots of Aftermarket Parts

jdgossner · 06-23-2012, 08:23 AM

Been trying to sell the whole bike but can't. Parting out instead. Most prices are shipped within continental US. Contact me for shipping on other items or outside US. Payment through paypal to joshgossner@hotmail.com . Please send as a gift and mention the item purchased. Feel free to call.

Added a bunch of pictures at the end of the thread. Suprised the intake and FCR are still around (very noticable improvement over stock). Also the resevoir front shocks and dynatek CDI.

Josh Gossner 724-678-7544

Engine, DRZe base gasket, DRZe springs, New style Hot cams, DRZe flywheel, case saver, MCCT, replaced cam chain all gears shift smooth. Could use the valves shimmed. Engine requires 93 octane fuel. $1,100 plus shipping

Dual piston front calipers from YFZ with good pads and break lines (stainless steel braided from calipers to main line, includes hard line but not rubber hose and master cylinder) $120 shipped

FCR Carb/Intake boots/Airbox/Thumber (FCR-39mm carb from ’05 YFZ – 165 MJ, 42 PJ, 50LJ, NCVQ needle on third clip / modified air box to fit clamp on UNI filter, comes with two 3x6” filters and EHS box lid / thumber and throttle cable for FCR) You will need to get a Raptor 660 petcock or buy my fuel tank to feed enough fuel to carb. $400 shipped

Stock front tires and wheels, about 30% tread, wheels a little dinged but very usable. $50 per set plus shipping - one set gone

Stock CDI $40 shipped
Stock Flywheel $40 shipped
Dynatek CDI (non-programable) $120 shipped
Heel Guards / Dual Pegs (modified heel guards to fit the dual pegs which are awesome) $60 shipped
Frame / Subframe (with Title) $400 plus shipping
Rear Shock (new lower bearing) $60 shipped
Rear shock linkage (new bearings) $30 shipped
Front Shocks (need lower bushings replaced) $150 shipped
A-arm (Upper/lower - Right) $40 shipped
Tie Rods with ends $40 shipped
Radiator / Fan / Reservoir $100 shipped
Rear Caliper and Res. (with Blue E-brake blockoff) $50 shipped
Oil Resevoir and hoses $30 shipped
Wire harness, reverse rev limiter removed, chopped the blob, comes with RM125 kill switch $30 shipped
Rad Gaurds (stock plastic) $15 shipped
Stock front calipers with almost new EBC Sintered pads $30 shipped

Master Cylinder-stock $20 shipped - SOLD
A-arm (Upper/lower - Left) $40 shipped -SOLD

Steering Stem $50 shipped - SOLD
Rear Axle w/o rotor (very slight tweek only noticeable on roadway) $100 shipped - SOLD
Stock Rear Wheels / Tires $50 plus shipping - SOLD
Stock Cams $30 shipped - SOLD
Seat, blue, no rips $60 shipped - SOLD
TAG fat Bars (w/ clamps and modified stock dash to fit) $60 shipped - SOLD
Front spindle / rotor (left) (new bearings) $40 shipped - SOLD
Clymer Maintenance manual $15 shipped SOLD
CT Sonic Full Exhaust $250 plus shipping SOLD
Tail Light $30 shipped SOLD
Headlight (not cracked but one bulb out) $30 shipped SOLD to DRMC
Battery (local pickup) – Brand new $30 SOLD
X-ring Chain / steel sprockets 13/40 gearing $40 Shipped SOLD to 1SICK470
MSR Clutch lever and cable (installed to replace the Blob) $20 shipped SOLD to 1SICK470
Skid Plate (Belly) w/ hardware $50 plus shipping SOLD
PRM Skid Plate (Rear) w/ hardware $100 shipped SOLD
PRM six-pack cooler rack (modified mounting plates using stainless bar stock) $40 shipped SOLD
PRM front bumper $40 shipped SOLD
Skid Plate (A-arms) w/ hardware $50 shipped SOLD
Front spindle / rotor (right) (new bearings) $40 shipped SOLD
Billet shifter Blue $15 shipped SOLD to Bergs
Billet Fuel Cap Blue $15 shipped SOLD
Rear Wheels/Tires, 22” Kenda Klaws, 50% tread, some plugs in them, Douglas wheels. $80 plus shipping SOLD
ODI Rogue Grips (120mm long) $20 shipped SOLD to DRMC
Plastic (Yellow), not perfect but no cracks $150 Plus shipping SOLD
Swing Arm w/ Bearing Carrier (new bearings in carrier and swinger) $150 plus shipping SOLD
Gas Tank w/ 660 petcock $30 shipped SOLD to lilRam86

lilram86 · 06-23-2012, 09:41 AM

I will take the gas tank with petcock, the tail light, and the headlight if in good condition. Do you have any pics. Also would like to see some pics of the heel guards with pegs. Thanks

jasmf24 · 06-23-2012, 10:44 AM

PM'd
Interested in front wheels.

BorderGuy · 06-23-2012, 04:41 PM

Can you post a pic of the fuel cap?

Edited- Sorry just read that its blue. Looking for a chrome one!

jdgossner · 06-23-2012, 07:34 PM

Deleted

jdgossner · 06-23-2012, 08:00 PM

sberg · 06-23-2012, 08:22 PM

Pics of the blue billet shifter? And I'll take the raptor petcock if the deal with lilram86 falls through.

What pads are on the YFZ calipers? Are you willing to sell them without the lines?

arrowblazer71 · 06-23-2012, 11:50 PM

pics of front bumper, im interested

yOGi420™ · 06-24-2012, 12:25 AM

Grips, how about $15 shipped? If so, I will send you the money immediately.

Jkolb · 06-24-2012, 02:53 AM

Im interested on MSR lever and gas cap. Thanks.

lilram86 · 06-24-2012, 01:51 PM

Let me know I will take the headlight, taillight, and gas tank with raptor petcock whenever you're ready.

Mikeb3119 · 06-24-2012, 02:18 PM

Someone should hop on that exhaust. Isnt it the best one for the Z?

lilram86 · 06-24-2012, 09:53 PM

Quote:

Originally Posted by Mikeb3119

Someone should hop on that exhaust. Isnt it the best one for the Z?

It is the best i have one on mine. Well worth the money sounds GREAT!!

jdgossner · 06-25-2012, 07:23 PM

Replied to PM's and hopefully responded to all questions. Let me know if I missed you. Supprised performance parts aren't moving. May need to list individually in performance forum.

yOGi420™ · 06-25-2012, 08:24 PM

$25 shipped for front calipers?

06-23-2012, 08:23 AM	#1 (permalink)
jdgossner :::Ozark 250 rider::: Join Date: Sep 2008 Location: McMurray, PA Posts: 283	2006 Part out - Lots of Aftermarket Parts Been trying to sell the whole bike but can't. Parting out instead. Most prices are shipped within continental US. Contact me for shipping on other items or outside US. Payment through paypal to joshgossner@hotmail.com . Please send as a gift and mention the item purchased. Feel free to call. Added a bunch of pictures at the end of the thread. Suprised the intake and FCR are still around (very noticable improvement over stock). Also the resevoir front shocks and dynatek CDI. Josh Gossner 724-678-7544 Engine, DRZe base gasket, DRZe springs, New style Hot cams, DRZe flywheel, case saver, MCCT, replaced cam chain all gears shift smooth. Could use the valves shimmed. Engine requires 93 octane fuel. $1,100 plus shipping Dual piston front calipers from YFZ with good pads and break lines (stainless steel braided from calipers to main line, includes hard line but not rubber hose and master cylinder) $120 shipped FCR Carb/Intake boots/Airbox/Thumber (FCR-39mm carb from ’05 YFZ – 165 MJ, 42 PJ, 50LJ, NCVQ needle on third clip / modified air box to fit clamp on UNI filter, comes with two 3x6” filters and EHS box lid / thumber and throttle cable for FCR) You will need to get a Raptor 660 petcock or buy my fuel tank to feed enough fuel to carb. $400 shipped Stock front tires and wheels, about 30% tread, wheels a little dinged but very usable. $50 per set plus shipping - one set gone Stock CDI $40 shipped Stock Flywheel $40 shipped Dynatek CDI (non-programable) $120 shipped Heel Guards / Dual Pegs (modified heel guards to fit the dual pegs which are awesome) $60 shipped Frame / Subframe (with Title) $400 plus shipping Rear Shock (new lower bearing) $60 shipped Rear shock linkage (new bearings) $30 shipped Front Shocks (need lower bushings replaced) $150 shipped A-arm (Upper/lower - Right) $40 shipped Tie Rods with ends $40 shipped Radiator / Fan / Reservoir $100 shipped Rear Caliper and Res. (with Blue E-brake blockoff) $50 shipped Oil Resevoir and hoses $30 shipped Wire harness, reverse rev limiter removed, chopped the blob, comes with RM125 kill switch $30 shipped Rad Gaurds (stock plastic) $15 shipped Stock front calipers with almost new EBC Sintered pads $30 shipped Master Cylinder-stock $20 shipped - SOLD A-arm (Upper/lower - Left) $40 shipped -SOLD Steering Stem $50 shipped - SOLD Rear Axle w/o rotor (very slight tweek only noticeable on roadway) $100 shipped - SOLD Stock Rear Wheels / Tires $50 plus shipping - SOLD Stock Cams $30 shipped - SOLD Seat, blue, no rips $60 shipped - SOLD TAG fat Bars (w/ clamps and modified stock dash to fit) $60 shipped - SOLD Front spindle / rotor (left) (new bearings) $40 shipped - SOLD Clymer Maintenance manual $15 shipped SOLD CT Sonic Full Exhaust $250 plus shipping SOLD Tail Light $30 shipped SOLD Headlight (not cracked but one bulb out) $30 shipped SOLD to DRMC Battery (local pickup) – Brand new $30 SOLD X-ring Chain / steel sprockets 13/40 gearing $40 Shipped SOLD to 1SICK470 MSR Clutch lever and cable (installed to replace the Blob) $20 shipped SOLD to 1SICK470 Skid Plate (Belly) w/ hardware $50 plus shipping SOLD PRM Skid Plate (Rear) w/ hardware $100 shipped SOLD PRM six-pack cooler rack (modified mounting plates using stainless bar stock) $40 shipped SOLD PRM front bumper $40 shipped SOLD Skid Plate (A-arms) w/ hardware $50 shipped SOLD Front spindle / rotor (right) (new bearings) $40 shipped SOLD Billet shifter Blue $15 shipped SOLD to Bergs Billet Fuel Cap Blue $15 shipped SOLD Rear Wheels/Tires, 22” Kenda Klaws, 50% tread, some plugs in them, Douglas wheels. $80 plus shipping SOLD ODI Rogue Grips (120mm long) $20 shipped SOLD to DRMC Plastic (Yellow), not perfect but no cracks $150 Plus shipping SOLD Swing Arm w/ Bearing Carrier (new bearings in carrier and swinger) $150 plus shipping SOLD Gas Tank w/ 660 petcock $30 shipped SOLD to lilRam86 __________________ '06 z400 22x11-9 Kenda Klaws Rears, 22x7-10 Stock Fronts 13/40 Gearing Full Exhaust - CT Sonic New style HotCams, DRZe flywheel Bypassed reverse rev limiter Primary Drives x-ring chain and sprocket kit FCR-39 ('05 YFZ - 165 MJ, 42 PJ, 50 LJ, NCVQ Needle on 3rd clip, 1.5 turn on fuel screw, o-ring mod), tors & tps removed, Motion Pro throttle cable, NAPA #1035 carb-to-head boot EHS Outerwears airbox lid, 3"x6" long clamp on UNI filter, snorkel removed, 400ex intake boot Riding at El. 1000 ft Last edited by jdgossner; 07-17-2012 at 11:06 PM.

06-23-2012, 09:41 AM	#2 (permalink)
lilram86 :::Rookie Rider::: Join Date: May 2009 Location: Huntington, WV Posts: 17	I will take the gas tank with petcock, the tail light, and the headlight if in good condition. Do you have any pics. Also would like to see some pics of the heel guards with pegs. Thanks __________________ 03' Z400 CT Racing Full Pipe Jet Kit Custom Air Intake Primary Drive 13T Front Primary Drive X-Ring Chain Maxxis Razr's All Way Around OMF Scoops

06-23-2012, 10:44 AM	#3 (permalink)
jasmf24 :::LT500 Rider::: Join Date: Mar 2011 Location: Pittsburgh Posts: 1,280	PM'd Interested in front wheels. __________________ 2004 KFX400, 12.2:1 Wiseco, HMF full exhaust, FCR-39 (170 M/ 42P/ 40L/ NCVQ, DRZ-E boot w/ compact head-stay), OSHC's, K-W valves w/ drz springs, Dyna Fs NP, Raptor Petcock, Wiseco cam chain, 400ex boot, Oversized clamp on UNI/K&N (no lid), DRZ-E Base, DRZ Flywheel, LTR450 Front Shocks, "Blob"-less ProTaper Contour bars (ATV High) w/ hot-start reverse, Odi grips, Tusk nerfs, Full skids, 14/40, (R) GBC X-Rex (F) Rzr2, Port & Polish by me. Last edited by jasmf24; 06-23-2012 at 10:49 AM.

06-23-2012, 04:41 PM	#4 (permalink)
BorderGuy :::Rookie Rider::: Join Date: Apr 2012 Location: Michigan Posts: 32	Can you post a pic of the fuel cap? Edited- Sorry just read that its blue. Looking for a chrome one! __________________ 2003 Z400 FMF Power Bomb FMF Silencer Jetted K&N Air Filter 2005 Z400 shocks w/rezzies Renthal chain and sprockets DG front bumber and nerf bars Douglas Rims ITP Holeshot Tires

06-23-2012, 07:34 PM	#5 (permalink)
jdgossner :::Ozark 250 rider::: Join Date: Sep 2008 Location: McMurray, PA Posts: 283	Deleted __________________ '06 z400 22x11-9 Kenda Klaws Rears, 22x7-10 Stock Fronts 13/40 Gearing Full Exhaust - CT Sonic New style HotCams, DRZe flywheel Bypassed reverse rev limiter Primary Drives x-ring chain and sprocket kit FCR-39 ('05 YFZ - 165 MJ, 42 PJ, 50 LJ, NCVQ Needle on 3rd clip, 1.5 turn on fuel screw, o-ring mod), tors & tps removed, Motion Pro throttle cable, NAPA #1035 carb-to-head boot EHS Outerwears airbox lid, 3"x6" long clamp on UNI filter, snorkel removed, 400ex intake boot Riding at El. 1000 ft Last edited by jdgossner; 06-25-2012 at 06:05 PM.

06-23-2012, 08:00 PM	#6 (permalink)
jdgossner :::Ozark 250 rider::: Join Date: Sep 2008 Location: McMurray, PA Posts: 283	__________________ '06 z400 22x11-9 Kenda Klaws Rears, 22x7-10 Stock Fronts 13/40 Gearing Full Exhaust - CT Sonic New style HotCams, DRZe flywheel Bypassed reverse rev limiter Primary Drives x-ring chain and sprocket kit FCR-39 ('05 YFZ - 165 MJ, 42 PJ, 50 LJ, NCVQ Needle on 3rd clip, 1.5 turn on fuel screw, o-ring mod), tors & tps removed, Motion Pro throttle cable, NAPA #1035 carb-to-head boot EHS Outerwears airbox lid, 3"x6" long clamp on UNI filter, snorkel removed, 400ex intake boot Riding at El. 1000 ft

06-23-2012, 08:22 PM	#7 (permalink)
sberg :::LT500 Rider::: Join Date: Nov 2009 Location: Mass Posts: 1,626	Pics of the blue billet shifter? And I'll take the raptor petcock if the deal with lilram86 falls through. What pads are on the YFZ calipers? Are you willing to sell them without the lines? __________________ QOTM Oct 2012 +2" JD MGC A-Arms - Axcaliber w/ Hubs - GT Thunder Shock Service & Link - K&N Powerlid and Uni - 400ex Boot - FCR39 - QS2- Ceramic Coated FMF Powerbomb - Alba Silencer - Pro Design Impellar - Supersprox - LSR Spindles - JD +1" Anti-Vibe Stem Service - Moose Bars - Streamline Lines - EBC Pads - ITP T-9 Pro 4/1 Fronts - Armadillo Chassis & Swing Skid - Blingstar Notorious Nerf/Peg/Heel - Works Frame Guards - HEP Guard Kit - IMS Tank - 6,000K HID Rebuild in progress

06-23-2012, 11:50 PM	#8 (permalink)
arrowblazer71 :::Z-250 Rider::: Join Date: Sep 2011 Location: Tarkio, MO Posts: 469	pics of front bumper, im interested __________________ 2004 Z400 white bros ehxaust, 92mm 4159 +5 hot rods stroker kit, Vertex piston, wiesco valves and timing chain,K&N filter w/ billet mount, pull choke, EBC brakes,AC Nerfs, Blingstar Bumper, PRM rear grab bar, Littlemissie MOD

06-24-2012, 12:25 AM	#9 (permalink)
yOGi420™ :::Get a life! You're over 5000 posts::: Join Date: Jul 2010 Location: Gateway To The Dunes, Cen Cal Posts: 6,353	Grips, how about $15 shipped? If so, I will send you the money immediately. __________________ 07 Suzuki LT Z400 (Future QOTM ) 04 Kawasaki KFX 400 (Dec. 2012 QOTM) 07 Can Am DS 250 (Oldest Son's) 07 Yamaha Raptor 50 (Youngest son) 07 Yamaha TT R50 (A Fun Little Toy) Need to install: DRZe Kit RatStack FCI Intake Ferrea Valves Athena 434 BBK Dynatech NP CDI IMS 4g Fuel Tank Titanium Wrist Pin Raptor 660 Petcock YFZ Thumb Throttle DID 520 ERT2 Chain K&N Crank Case Filter Web Cams 539/539+3 CP 94mm 12.5:1 Piston FCR-39 from 450 Outlaw Last edited by yOGi420™; 06-24-2012 at 12:30 AM.

06-24-2012, 02:53 AM	#10 (permalink)
Jkolb :::LT500 Rider::: Join Date: Dec 2011 Location: Twain Harte, CA Posts: 1,187	Im interested on MSR lever and gas cap. Thanks. __________________ New ride is a 2002 yz426. All stock! Traded 04' z400 K&N Air filter/Uni James dean jetting Alba full exhaust 12:1 Compression piston Acerbis hand guards AC Nerfs

06-24-2012, 01:51 PM	#11 (permalink)
lilram86 :::Rookie Rider::: Join Date: May 2009 Location: Huntington, WV Posts: 17	Let me know I will take the headlight, taillight, and gas tank with raptor petcock whenever you're ready. __________________ 03' Z400 CT Racing Full Pipe Jet Kit Custom Air Intake Primary Drive 13T Front Primary Drive X-Ring Chain Maxxis Razr's All Way Around OMF Scoops

06-24-2012, 02:18 PM	#12 (permalink)
Mikeb3119 :::LT500 Rider::: Join Date: Jun 2011 Location: Houston, TX Posts: 1,503	Someone should hop on that exhaust. Isnt it the best one for the Z? __________________ 04 Z434 CW 434 BBK yoshi rs-3 ferrea valves drze springs velocity intake 12.5:1 vertex piston NSHC DID cam chain ACCT mod Barnett custom 05+ CF clutch Raptor petcock mod 40mm fcr 450r carb dyna programmable hotrods oem spec crank hotrods crank bearings 05 & up rezzy shocks Lonestar +3 a arms

06-25-2012, 07:23 PM	#14 (permalink)
jdgossner :::Ozark 250 rider::: Join Date: Sep 2008 Location: McMurray, PA Posts: 283	Replied to PM's and hopefully responded to all questions. Let me know if I missed you. Supprised performance parts aren't moving. May need to list individually in performance forum. __________________ '06 z400 22x11-9 Kenda Klaws Rears, 22x7-10 Stock Fronts 13/40 Gearing Full Exhaust - CT Sonic New style HotCams, DRZe flywheel Bypassed reverse rev limiter Primary Drives x-ring chain and sprocket kit FCR-39 ('05 YFZ - 165 MJ, 42 PJ, 50 LJ, NCVQ Needle on 3rd clip, 1.5 turn on fuel screw, o-ring mod), tors & tps removed, Motion Pro throttle cable, NAPA #1035 carb-to-head boot EHS Outerwears airbox lid, 3"x6" long clamp on UNI filter, snorkel removed, 400ex intake boot Riding at El. 1000 ft Last edited by jdgossner; 06-25-2012 at 07:26 PM.

06-25-2012, 08:24 PM	#15 (permalink)
yOGi420™ :::Get a life! You're over 5000 posts::: Join Date: Jul 2010 Location: Gateway To The Dunes, Cen Cal Posts: 6,353	$25 shipped for front calipers? __________________ 07 Suzuki LT Z400 (Future QOTM ) 04 Kawasaki KFX 400 (Dec. 2012 QOTM) 07 Can Am DS 250 (Oldest Son's) 07 Yamaha Raptor 50 (Youngest son) 07 Yamaha TT R50 (A Fun Little Toy) Need to install: DRZe Kit RatStack FCI Intake Ferrea Valves Athena 434 BBK Dynatech NP CDI IMS 4g Fuel Tank Titanium Wrist Pin Raptor 660 Petcock YFZ Thumb Throttle DID 520 ERT2 Chain K&N Crank Case Filter Web Cams 539/539+3 CP 94mm 12.5:1 Piston FCR-39 from 450 Outlaw

Remove Advertisements Sponsored Links
SuzukiCentral.com Advertisement