Suzuki Z400 Forum : Z400 Forums - Search Results
Advanced Search
Showing results 1 to 25 of 500
Search took 0.27 seconds.
Search: Posts Made By: jetmech25
Forum: New Member Introductions   Today, 12:31 PM
Replies: 6
Views: 42
Posted By jetmech25
With all of that and still no luck, Iíd suspect a...

With all of that and still no luck, Iíd suspect a CDI plug had a wire burned or pin pulled out, or the CDI itself took a dump. Take a really good look at the pins on the connector at the CDI. The...
Forum: Maintenance/Repairs/Tuning   Today, 01:24 AM
Replies: 3
Views: 35
Posted By jetmech25
Maybe the springs are worn then. Can you hear a...

Maybe the springs are worn then. Can you hear a big clunk when you hit the throttle?
Forum: Maintenance/Repairs/Tuning   Yesterday, 08:04 PM
Replies: 3
Views: 35
Posted By jetmech25
Iím guessing you have a worn clutch basket. The...

Iím guessing you have a worn clutch basket. The clutch plates get caught in ďgroovesĒ worn into the fingers of the clutch basket and doesnít fully seat until you give it some throttle. If thatís the...
Forum: New Member Introductions   Yesterday, 01:17 PM
Replies: 2
Views: 30
Posted By jetmech25
Welcome! Please repost your issue in the...

Welcome! Please repost your issue in the Maintenance section.
Forum: New Member Introductions   Yesterday, 01:14 PM
Replies: 6
Views: 42
Posted By jetmech25
Doesnít really answer my question, but with all...

Doesnít really answer my question, but with all of that work being done at once, it could be any number of things.
Try starting on prime (or just get rid of that junk factory petcok and put on a...
Forum: New Member Introductions   07-15-2019, 05:37 PM
Replies: 6
Views: 42
Posted By jetmech25
So, all of that was done, then reassembled, then...

So, all of that was done, then reassembled, then ran great, then suddenly died? In that order?
Forum: New Member Introductions   07-12-2019, 03:21 AM
Replies: 1
Views: 31
Posted By jetmech25
If you mean 92200C and 92200D in this microfiche,...

If you mean 92200C and 92200D in this microfiche, then yes. Re-use it, but it should be behind the entire stack, not between them. Make sure you soak the new plates in oil overnight before installing...
Forum: New Member Introductions   07-09-2019, 12:26 PM
Replies: 2
Views: 50
Posted By jetmech25
Welcome back!

Welcome back!
Forum: LT-Z400   07-06-2019, 10:57 PM
Replies: 8
Views: 310
Posted By jetmech25
Donít we all? 😂 Start a new post if you have...

Donít we all? 😂

Start a new post if you have a problem.
Forum: Maintenance/Repairs/Tuning   07-05-2019, 05:40 PM
Replies: 4
Views: 65
Posted By jetmech25
I reused my factory keepers with KW valves. No...

I reused my factory keepers with KW valves. No problems.
Forum: New Member Introductions   07-05-2019, 03:24 AM
Replies: 9
Views: 75
Posted By jetmech25
I get most of my stuff from the Cycle Gear...

I get most of my stuff from the Cycle Gear clearance rack. 😂
Forum: Suzuki Loft   07-03-2019, 07:56 PM
Replies: 2
Views: 63
Posted By jetmech25
Rip.

Rip.
Forum: New Member Introductions   07-03-2019, 11:34 AM
Replies: 9
Views: 75
Posted By jetmech25
Welcome!

Welcome!
Forum: New Member Introductions   07-01-2019, 05:28 PM
Replies: 3
Views: 56
Posted By jetmech25
Check the 30 amp fuse next to the relay. They...

Check the 30 amp fuse next to the relay. They sometimes pop when replacing the battery. There should be a spare there to replace it with, but itíll pop too if you have burned wiring. Might be time...
Forum: Maintenance/Repairs/Tuning   06-30-2019, 01:32 PM
Replies: 4
Views: 73
Posted By jetmech25
01-05 works.

01-05 works.
Forum: Maintenance/Repairs/Tuning   06-30-2019, 12:38 PM
Replies: 4
Views: 73
Posted By jetmech25
Petcok is bad. Swap to the raptor660 petcok....

Petcok is bad. Swap to the raptor660 petcok. Works great and you’ll have an off position. Costs about $30. Get an actual Yamaha part, not Chinese knockoffs on eBay. Just swap it out and plug the...
Forum: Maintenance/Repairs/Tuning   06-30-2019, 12:35 PM
Replies: 13
Views: 161
Posted By jetmech25
Shouldnít have been an issue then unless one...

Shouldnít have been an issue then unless one failed. Maybe your clamp falling in there cracked one and it finally failed. 🤷Wooter♂️
Forum: Maintenance/Repairs/Tuning   06-29-2019, 11:32 PM
Replies: 13
Views: 161
Posted By jetmech25
When you swapped the valves, were the springs...

When you swapped the valves, were the springs replaced with dual-coil springs?
Forum: Maintenance/Repairs/Tuning   06-29-2019, 05:03 PM
Replies: 25
Views: 338
Posted By jetmech25
I get fed up sometimes and take it to a shop,...

I get fed up sometimes and take it to a shop, usually regret it. Youíll probably need a new battery anyway, but check it first. Then see if its any different.
Forum: Maintenance/Repairs/Tuning   06-28-2019, 07:27 PM
Replies: 25
Views: 338
Posted By jetmech25
It could be. I guess I assumed you had a charger...

It could be. I guess I assumed you had a charger with a “jump” feature like mine. If the battery sat in a drained condition for very long, it’ll never charge back to a full state. The best it’ll do...
Forum: Maintenance/Repairs/Tuning   06-28-2019, 04:29 PM
Replies: 25
Views: 338
Posted By jetmech25
Yeah, starter is probably corroded to death...

Yeah, starter is probably corroded to death inside. Warranties are always cool!
Forum: Maintenance/Repairs/Tuning   06-28-2019, 02:06 PM
Replies: 25
Views: 338
Posted By jetmech25
Starter is crazy-easy to swap. New is like...

Starter is crazy-easy to swap. New is like $300-400 for the part. I’d try my luck on fleabay.

I imagine they charge a half-hour or an hour minimum for each part. So, could be as much as $200 in...
Forum: Suzuki Loft   06-27-2019, 07:51 PM
Replies: 1
Views: 48
Posted By jetmech25
First guess: dirty carb. Second, limited...

First guess: dirty carb.

Second, limited fuel supply, such as a stuck float or partially-clogged petcok.

I take it that it’s different than the rev limiter.
Forum: Maintenance/Repairs/Tuning   06-26-2019, 08:00 PM
Replies: 13
Views: 161
Posted By jetmech25
It would, but could have jumped timing if the...

It would, but could have jumped timing if the tensioner failed or a gear spun on one of the cams. The lower timing gear could also be loose. Without investigating further, probably a failed valve.
Forum: Maintenance/Repairs/Tuning   06-26-2019, 01:07 PM
Replies: 1
Views: 49
Posted By jetmech25
Leaking gas out of the overflow tube? The float...

Leaking gas out of the overflow tube? The float needle isnít seated. No matter how good you clean it, it seems there is always some loose dirt floating around and it gets stuck in the float needle...
Showing results 1 to 25 of 500

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome